Heritage

Looking after a bluestone home in Adelaide

How Adelaide's bluestone and sandstone homes were built, why lime mortar matters, what causes cracks and salt damp in old stone walls, and the heritage overlays that apply.

Bluestone villa with red-brick quoins, an arched timber front door, a bullnose verandah with lacework and a white picket fence

In short

Adelaide's bluestone and sandstone homes were built with soft lime mortar, often on shallow footings, and much of Adelaide sits on highly reactive clay. Keep water away from the walls, repoint in lime rather than hard cement, and treat salt damp as its own problem. Have cracks of 5 mm or more, bulging walls or badly decayed stone checked by an engineer, and check heritage overlays before changing anything.

Key takeaways

  • Lime mortar is meant to be softer than the stone. Hard cement repointing traps moisture and salt and pushes the damage into the stone.
  • Salt damp decay usually sits about 0.5 to 1.2 m above the ground. Damp-proof course work is a specialist's job; the engineer looks at stability.
  • Cracks of 5 mm or more, cracks that keep growing, and walls that lean or bulge need an engineer's assessment.
  • In a Historic Area, demolition is restricted unless the original building's structural integrity or safe condition is beyond reasonable repair.

Bluestone and sandstone villas and cottages are part of what makes Adelaide look like Adelaide, from Norwood and Unley to Gawler and Port Adelaide. They were built to last, but they were built differently from a modern house, and most of the damage we see in them comes from treating them as if they weren't.

Bluestone homes: quick facts

Walls
Bluestone, sandstone or limestone, often with red-brick quoins
Mortar
Soft lime mortar and render
Salt damp zone
About 0.5 to 1.2 m above ground
Ground
Much of Adelaide sits on highly reactive clay
Historic Area Statements
Unley 28, Norwood Payneham & St Peters 26
Our assessment
Fixed quote per home

How were Adelaide's bluestone and sandstone homes built?

They were typically built with stone walls laid in lime mortar, often finished with lime render, on shallow footings. Early colonial buildings used limestone, bluestone and sandstone, and Federation and Edwardian houses often paired red brick with contrasting stone. Red-brick quoins at the corners and around windows are a familiar Adelaide detail.

The Code's Historic Area Statements record the materials area by area:

  • Norwood: late 19th-century single- and double-fronted cottages in bluestone, sandstone, pisé or brick
  • Unley Park: houses built from 1900 to 1940 in sandstone, bluestone and brick
  • Gawler East: villas and symmetrical cottages in sandstone or limestone with red-brick quoins
  • Medindie: houses mostly built of locally sourced sandstone or bluestone

Many older stone walls are two faces of stone with rubble between them, rather than solid blocks right through. That matters when a wall bulges, when an opening is cut through it, or when the base is replaced during salt damp work.

Why does lime mortar matter in a bluestone wall?

Lime mortar is softer and more porous than the stone, so moisture and salt leave the wall through the joints, and the joints wear first. Repointing is meant to be a routine, replaceable job; the stone isn't.

Rough-faced sandstone wall with red-brick quoins around a timber sash window, weathered mortar and a hairline crack running from the sill
Figure 1Weathered lime joints and a hairline crack under a sill: the joints are meant to wear before the stone does.

Hard cement mortar and cement render reverse that. The water and salt can't get out through the joints, so they come out through the stone and brick instead, which then crumble or flake. Cement is also stiffer, so a wall that used to absorb small seasonal movement in its joints cracks through the stone. Heritage practice is to repoint and render old stone in lime, and the City of Adelaide publishes heritage specifications for salt damp work and undersetting.

Why do bluestone and sandstone walls crack?

Most cracks in old stone walls come from ground movement under shallow footings, from openings and lintels, or from decay at the base of the wall. Much of Adelaide sits on highly reactive clay; every site needs its own classification. South Australia also has the highest share of houses with major ceiling or floor cracks, at 6.5% in ABS data for 2019–20.

What you seeCommon causeWhat the engineer checks
Diagonal cracks from window and door cornersFooting movement on reactive clay, often seasonalCrack widths over time, floor levels, drainage, trees
Cracks over openings, a dropped arch or lintelDecayed or undersized lintel, or movement belowThe lintel, the bearing at each end, the wall above
A corner separating, cracks near downpipesWater softening or swelling the clay at one pointStormwater, leaking pipes, paving falls
Bulging or leaning wallFaces of a rubble wall separating, or roof spreadHow the wall faces are tied together, the roof structure, how far it has moved
Crumbling stone and mortar at the baseSalt dampWhether the decay affects stability
Close-up of a crack running through bluestone blocks and lime mortar beside red-brick quoins and a timber window frame
Figure 2A crack running through the stone, not just the joints, is worth having measured and monitored.

Crack width is a guide, not a verdict. A crack of 5 mm or more is moderate damage on the AS 2870 scale, but the pattern, location and whether it is still moving matter as much. See cracks in walls in Adelaide and our cracks and footing movement report, from $990 + GST ($1,089 inc GST).

Is it salt damp or a structural problem?

Salt damp is usually a moisture and salt problem, and it becomes structural when the masonry has decayed enough to affect the wall's stability. "Salt damp" is a term widely used in South Australia, and Adelaide is known for it because of hot, drying summers and very salty soils. Typical decay sits about 0.5 to 1.2 m above the ground.

Base of an old bluestone wall with red-brick quoins, showing white salt efflorescence, crumbling mortar and flaking bricks beside a gravel path
Figure 3White salt, crumbling joints and flaking brick at the base of a wall are classic salt damp. The structural question is how deep the decay goes.
  • Damp-proof course work is a damp specialist's job: injection, undersetting, lime render and drainage changes.
  • Undersetting replaces the base of a wall in sections with a new damp-proof course. It should not be confused with underpinning, which treats structural cracking from settlement or footing failure.
  • Bring in an engineer for structural cracking, temporary support while high or thick rubble walls are underset, or masonry so decayed that stability is affected.

We don't sell or carry out salt damp treatment, so our salt damp structural assessment (from $990 + GST ($1,089 inc GST)) is only about what the damp has done to the walls. See also salt damp or structural cracking.

How do you look after a bluestone home?

Keep water away from the base of the walls, keep the joints soft, and find the cause of any movement before anyone repairs it.

Do

  • Keep gutters, downpipes and stormwater pipes working and discharging away from the walls
  • Keep ground, paths and garden beds below the damp-proof course and falling away from the house
  • Repoint and render in lime mortar, matched to the wall
  • Mark and date the ends of cracks so you can see whether they move

Don't

  • Cement-render or cement-repoint the base of an old stone wall
  • Pile soil, mulch or paving up against the walls
  • Install air drains in reactive clay without geotechnical engineering advice
  • Agree to underpinning or resin injection before the cause is confirmed

If a contractor has already quoted underpinning or resin injection, an independent second opinion from $350 + GST ($385 inc GST) tells you whether it's needed and, if it is, how much and where.

What heritage rules apply to a bluestone home in Adelaide?

That depends on which of four heritage layers, if any, cover your property. Check the address on PlanSA, because the layer decides what you can change and what needs approval.

LayerWhat it means for owners
State Heritage PlaceListed under the Heritage Places Act 1993. The usual "not development" exemptions in Schedule 4 don't apply.
Local Heritage Place OverlayDemolition is assessed against PO 6.1. Exemptions for small retaining walls and pergolas don't apply.
Historic Area OverlayDemolition is restricted (PO 7.1) unless the front has been substantially altered and can't reasonably be restored, or the original building's "structural integrity or safe condition" is "beyond reasonable repair". Decks and front fences lose their exemptions.
Character Area OverlayDifferent rules from a Historic Area. Check with your council what needs approval for your plans.

Planning and Design Code v2026.19 and PDI (General) Regulations 2017. Unley has 28 Historic Area Statements, the most of any council, and Norwood Payneham & St Peters 26.

Because of PO 7.1, an engineer's structural condition report is central to any demolition application in a Historic Area. It has to show the real condition of the building and whether it can reasonably be repaired, not just that it has cracks. See our bluestone and heritage homes service.

What should you check before buying a bluestone home?

Check the walls, the base, the drainage and the overlays. Old stone homes last well when they are looked after, but the costs that matter are structural and can sit behind fresh paint or render.

  • Cracks over windows and doors, at corners and through the stone
  • Decay, fresh render or new paint at the base of the walls
  • Cement repointing or render on the stone
  • Floors that slope and doors that stick
  • Downpipes, paving falls and large trees close to the walls
  • The heritage overlay, if you plan to extend or rebuild

A building inspection covers the whole house, and an engineer answers the structural questions it raises. See building inspector or structural engineer and our pre-purchase structural inspection, from $990 + GST ($1,089 inc GST).

When should you call a structural engineer about a bluestone home?

  • Cracks 5 mm or wider, cracks through the stone, or cracks that keep growing
  • A wall leans or bulges, or a corner is pulling away
  • An arch or lintel has dropped over a door or window
  • Salt damp decay is deep, or undersetting is planned on a high or thick wall
  • You've been quoted underpinning, resin injection or a rebuild and want an independent view
  • You need a condition report for a Historic Area demolition or alteration application

What to send

Photos of each wall, close up and from further back, with the suburb and any quotes or reports. Get a fixed quote in under 20 minutes on average, during business hours, or call 08 7083 9853.

Sources

  1. City of Adelaide, Architectural periods and styles in the City of Adelaide
  2. City of Adelaide, Heritage resources. Specifications for damp-proof injection, salt damp management and undersetting
  3. David Young, Salt attack and rising damp: a guide to salt damp in historic and older buildings (2008). Written with heritage bodies including SA's Department for Environment and Heritage and Adelaide City Council
  4. PlanSA, Planning and Design Code, Version 2026.19 (8 October 2026). Historic Area Overlay PO 7.1, Local Heritage Place Overlay PO 6.1, Historic Area Statements
  5. Planning, Development and Infrastructure (General) Regulations 2017. Reg 3C and Schedule 4 (work that is not development)
  6. InDaily, Cracking up: SA's nation-leading house faults (ABS data for 2019–20)

FAQ

Bluestone and sandstone homes: FAQs

Still unsure? Call 08 7083 9853 or send photos for a fixed quote.

Should bluestone be repointed with lime or cement mortar?

Lime, in almost every case. Old stone walls were built with soft lime mortar that lets moisture and salt out through the joints; a hard cement mortar traps them and moves the decay into the stone and brick.

Are cracks in a bluestone wall serious?

Many are minor and old. A crack of 5 mm or more, a crack that keeps widening, cracks over doors and windows, or a wall that leans or bulges should be assessed by an engineer before anyone quotes a repair.

Is salt damp a structural problem?

Usually not on its own. It becomes structural when the masonry at the base of the wall has decayed enough to affect stability, or when undersetting a high or thick rubble wall needs temporary support.

What is the difference between undersetting and underpinning?

Undersetting replaces the base of a wall in short sections to insert a new damp-proof course; it is a salt damp treatment. Underpinning deepens or strengthens a footing to treat structural movement from settlement or footing failure.

Can I demolish a bluestone house in a Historic Area?

Only in limited cases. The Historic Area Overlay (PO 7.1) allows demolition of a building showing the area's historic characteristics only if its front has been substantially altered and can't reasonably be restored, or if its structural integrity or safe condition is beyond reasonable repair, which is where an engineer's condition report comes in.

What should I check before buying a bluestone house?

Look for cracks over openings and at corners, decay at the base of the walls, cement render or repointing, poor drainage and large trees close by, and check the heritage overlays on PlanSA. A pre-purchase structural inspection covers the structure.

How much does a structural assessment of a heritage home cost?

We give bluestone and heritage homes a fixed quote, because wall construction, access and the question being asked vary a lot. Send photos and you get the price in under 20 minutes on average, during business hours.

Do you repair bluestone walls?

No. We are engineering only: we assess, diagnose and design, and we never sell or carry out repairs, repointing or salt damp treatment. That keeps the advice about your house, not a job.