In short
Salt damp shows as a band of crumbling mortar, flaking brick or stone and white salt, usually about 0.5 to 1.2 m above the ground. Structural movement shows as cracks that step, taper or run diagonally from windows and doors. Treating salt damp is a damp specialist's job; an engineer is needed for cracking, temporary support during undersetting, or masonry so decayed that stability is at risk.
Key takeaways
- "Adelaide is well known for its bad salt damp": hot, drying summers and very salty soils draw salts into old walls.
- Salt damp decay usually sits in a band about 0.5–1.2 m above the ground. Movement cracks can run anywhere.
- Undersetting replaces the wall base in sections with a new damp-proof course. It "should not be confused with underpinning".
- High walls and thick rubble walls may need an engineer's advice and temporary support while they are underset.
- We assess the structural side only. Damp treatment is for a damp specialist, and we don't sell it.
Old Adelaide walls take a beating from below. Salty, damp ground and hot summers break down the base of bluestone, sandstone and brick, and reactive clay moves the footings under them. The two problems can look alike from the footpath, and they need different people. This guide explains how to tell salt damp from structural movement, what to do when you have both, and why the word "undersetting" so often gets confused with underpinning.
Salt damp or structural: quick facts
- Salt damp
- A band of decay about 0.5–1.2 m above the ground
- Movement
- Cracks that step, taper or run from openings
- Damp treatment
- A damp specialist: damp-proof course, undersetting, render
- Engineer
- Cracking, temporary support, decay affecting stability
- Undersetting
- New damp-proof course in the wall base, not underpinning
- Our assessment
- From $990 + GST ($1,089 inc GST)
What is salt damp?
Salt damp is decay of masonry caused by moisture rising from the ground and the salts it carries. "Salt damp is a term widely used in South Australia," writes David Young in Salt attack and rising damp, a guide prepared with heritage bodies including SA's Department for Environment and Heritage and Adelaide City Council, and "Adelaide is well known for its bad salt damp" because of its hot, drying summers and very salty soils.
Early Adelaide buildings used limestone, bluestone and sandstone with lime mortar and render, and Federation and Edwardian houses added red brick with contrasting stone. In walls without an effective damp-proof course, water rises, evaporates near the surface and leaves salt crystals behind. Over years the crystals break up the mortar, then the face of the brick or stone. The guide puts typical decay at about 0.5 to 1.2 m above the ground.
How do you tell salt damp from structural cracking?
Look at where the damage is and what shape it takes: salt damp is a band of surface decay near the base of the wall, while structural movement is a crack with a direction. This quick flow sorts most cases.
Is the damage a band low on the wall?
Crumbling or powdery mortar, flaking brick or stone, white salts, bubbling paint and damp plaster, mostly below about 1.2 m.
Yes: likely salt damp, a damp specialist's jobNo: go to the next questionIs there a crack that steps, tapers or runs from a window or door corner?
Especially one you can see inside and outside the same wall.
Yes: likely movement: crack and footing reportNo: go to the next questionDo doors stick, or floors slope?
Movement in more than one place usually means the footings have moved.
Yes: structural movement is likelyNo: monitor and treat the dampAre stones loose, joints hollow deep into the wall, or the base bulging?
Decay this deep is no longer only a surface problem.
Yes: an engineer before treatment: salt damp structural assessmentNo: damp treatment, then watch it
What do the signs look like side by side?
Salt damp damages the surface in a band at the base; structural movement cracks the wall along a line.
| Sign | Salt damp | Structural movement |
|---|---|---|
| Where | A band about 0.5–1.2 m above the ground | Anywhere: often from corners of windows and doors, at wall junctions or below the eaves |
| What you see | White salts, powdery mortar, flaking brick, fretting stone, bubbling paint and plaster | Cracks that step through joints, taper, run diagonally or cut through bricks and stones |
| Inside | Damp, stained or blown plaster low on the wall, decayed skirtings | Cracked plaster in line with the outside crack, sticking doors, sloping floors |
| Over time | Slow, steady loss of surface; salts bloom as the wall dries | Cracks open and close with the clay, or keep widening |
| Who to call | A damp specialist | An independent structural engineer |
A guide only. Many older homes show both, so the cause is confirmed on site.

What if a wall has salt damp and cracks?
Then both need dealing with, usually in the right order: the structural question first, so the damp work doesn't hide or worsen a moving wall. Water is often the link. A leaking pipe or a downpipe emptying at the wall wets the masonry and the clay under the footing at the same time, and a 2016 study of one Adelaide site found the clay reacted to ponding and leaking service pipes. Deep decay can also weaken a wall base until it cracks under its own weight.
An engineer's assessment sorts out which cracks are movement and which are decay, grades them on the AS 2870 scale, checks lintels and corners, and says what support the wall needs before any treatment starts. Our cracks in walls guide explains the crack scale.
Is undersetting the same as underpinning?
No. Undersetting replaces the base of a wall in sections with a new damp-proof course, and Young's guide says it "should not be confused with underpinning, which is a treatment for structural cracking due to settlement or footing failure". Undersetting cuts out and rebuilds the lowest courses of the wall itself; underpinning deepens or adds support under the footing.
| Question | Undersetting | Underpinning |
|---|---|---|
| Treats | Salt damp | Settlement or footing failure |
| Works on | The base of the wall, in short sections | The footing and the ground below it |
| Done by | Damp and masonry specialists | Builders, to an engineer's design |
| Engineer needed? | For high walls, thick rubble walls and temporary support | Yes: diagnosis and design |
The engineering in undersetting is the temporary support. "Undersetting of high walls may need structural engineering advice," the guide says, and thick rubble walls may need temporary support while each section is out. We design that support and the sequence, and check the wall above, without selling the undersetting. If someone has quoted you for underpinning a damp wall, read how much does underpinning cost and get the cause confirmed first.
Who does what with a salt damp wall?
The damp specialist treats the damp; the engineer answers the structural questions. We stay on our side of that line.
A damp specialist
- Damp-proof course injection or undersetting
- Salt-retardant render and lime repointing
- Drainage and ground levels against the wall
- Doesn't diagnose footing movement or design support
An independent engineer
- Sorts movement cracks from decay, on the AS 2870 scale
- Checks lintels, corners and decayed masonry for stability
- Designs temporary support for undersetting
- Never sells, recommends a contractor for or carries out the treatment
Drainage on clay needs care
Young's guide warns that air drains "should never be installed in reactive clay soils without geotechnical engineering advice". Drying or wetting the ground beside a footing on clay can start the very movement you are trying to avoid.
The City of Adelaide publishes specifications for damp-proof injection, salt damp management and undersetting, which are useful when you compare treatment quotes. If the house is a heritage place, check with your council before work starts.
When to call a structural engineer
Call an engineer when the damp wall also shows signs of movement, or before anyone cuts into it.
- Cracks step, taper or run from openings, especially above the damp band
- Stones are loose, joints are hollow deep into the wall, or the base bulges
- A high or thick rubble wall is about to be underset
- Doors stick or floors slope as well as the walls being damp
- You're buying an older home with salt damp and cracks. See our pre-purchase structural inspection
The structural side, independently
Our salt damp structural assessment starts from $990 + GST ($1,089 inc GST). Send photos of the wall base and any cracks for a fixed quote in under 20 minutes on average, during business hours.
Need an engineer?
Damp walls and cracks?
Send photos of the wall base and any cracks. You'll have a fixed quote for the structural assessment in under 20 minutes on average, during business hours.
Sources
- D. Young, Salt attack and rising damp: a guide to salt damp in historic and older buildings (2008), prepared with heritage bodies including SA's Department for Environment and Heritage and Adelaide City Council
- City of Adelaide, Heritage resources: specifications for damp-proof injection, salt damp management and undersetting
- City of Adelaide, Architectural periods and styles in the City of Adelaide
- Standards Australia, AS 2870-2011 Residential slabs and footings. Appendix C, Table C1: classification of damage to walls
- Sheard and others (2016), reactive soil study, SARIG report d20011047. Clay reaction to ponding and leaking service pipes
