Widened opening in an older house with exposed brick ends, a new steel beam held on three adjustable steel props, plaster dust on the floorboards and an open kitchen and living room behind

Homeowners · Builders · Renovators

Load-bearing wall removal and beam design

Opening up a villa or a 1960s brick home means moving the load a wall carries onto a new beam, posts and footings. In South Australia that needs approval. We design it and document it; your builder does the work.

  • From $790+ GST ($869 inc GST)
  • Under 20 minaverage time to a fixed quote
  • Approvalneeded to remove a load-bearing wall
Quote requestMon–Fri 8am–5pm

Get a fixed quote for your beam design

Photos of the wall from both sides, the room sizes and a photo of the roof space above it are usually enough.

We reply with a fixed quote in under 20 minutes on average, during business hours.

Engineering only
Beam designs from $790 + GST
Quotes in under 20 min on average
NCC & Australian Standards

In short

Removing a load-bearing wall in South Australia is not exempt work, so it needs Building Rules Consent from your council or a building certifier, with an engineer's design for the beam, posts and footings. Our wall removal and beam designs in Adelaide start from $790 + GST ($869 inc GST). We design and document the work only; we never carry out wall removal or recommend who does.

Fee
From $790 + GST ($869 inc GST)
We need
Photos of the wall, the roof space above it and the room sizes
You receive
Beam, post and footing design with drawings and calculations

Before you start

How can you tell if a wall is load bearing?

A wall is load bearing if it carries roof, ceiling or floor loads down to a footing, and the way to tell is to look above it and below it, not just at the room. In Adelaide houses the signs depend on when the house was built.

  • Ceiling joists or roof struts land on it. Lift the manhole and look along the top of the wall with a torch.
  • It is solid brick or stone. In bluestone and sandstone villas, many internal walls are masonry and help hold up the roof and the outer walls.
  • It stands on its own footing. Adelaide houses are mostly solid masonry on dwarf wall footings or raft slabs, and a wall with its own footing or slab thickening below is usually structural.
  • It used to be an outside wall before an extension or lean-to was added behind it.
  • A floor or another wall sits on it in a two-storey house.

A wall that carries no roof can still matter. In timber-framed houses some internal walls are bracing walls that stiffen the house against wind, and in masonry houses cross walls stop long outer walls from leaning. Adelaide's earthquake hazard is the highest of the capital cities and is part of our design checks, so we look at bracing as well as the beam.

Key takeaways

  • The roof space and what's under the floor show whether a wall is load bearing. The room alone doesn't.
  • The beam is only half the job: posts and footings carry its load to the ground.
  • Some walls carry no roof but still brace the house.
  • A load-bearing wall can't come out in SA without approval.

Photos that help us quote

Both sides of the wall, the ceiling along it, and the roof framing directly above (lift the manhole and use a torch). Add the floor beside the wall: a slab, or floorboards over a timber subfloor.

South Australian rules

Do you need approval to remove a load-bearing wall in SA?

Yes. Internal alterations are exempt only when they remove nothing more than fixtures, fittings or non-load-bearing partitions and won't affect the structural soundness of the building, so taking out a load-bearing wall needs approval.

The workApprovalWhat the engineer provides
Removing fixtures, fittings or a non-load-bearing partition, with no effect on structural soundnessExempt (not development)Nothing for approval. We can confirm from photos that the wall carries no load and isn't a bracing wall
Removing or shortening a load-bearing wall, or widening an opening in oneBuilding Rules Consent from your council or an accredited professional, lodged on PlanSABeam, post and footing design, with drawings and calculations
Any work on a State Heritage PlaceThe exemptions don't applyThe design and documents; your council confirms the heritage approvals
A wall already removed without approvalYour council or certifier advises on the approval pathAn inspection of what was built, any fix designed, and the certification they ask for

Planning, Development and Infrastructure (General) Regulations 2017, Schedule 4 clause 4(4) and regulation 3C. Your council or certifier confirms what your job needs. More in our guide to building approvals in SA.

Who does what

Applications are lodged on PlanSA. Building Rules Consent comes from your council or an accredited professional (a building certifier). Your builder gives one business day's notice before work starts and before it is finished.

At completion the builder signs Part A of the Statement of Compliance and you sign Part B, lodged with any certificates or reports your consent lists. If the building work costs $20,000 or more, your builder also needs building indemnity insurance, because the work needs approval.

Independent certification of the calculations

Building Level 2 and Level 3 certifiers can only grant consent once the structural calculations are certified by an independent technical expert: someone who had no part in the design and has no financial interest in it.

We can design your beam, or independently certify calculations someone else prepared, from $390 + GST ($429 inc GST). We can't do both on the same job. See engineer's certificates and independent certification.

What's included

What does a beam design include?

A beam design covers everything between the roof and the ground: the beam, the posts or piers at each end, the footings under them and the connections, on drawings with calculations for your builder and certifier.

  • What the wall carries: roof, ceiling, any storey above, and point loads such as solar panels, a hot water service or a tank
  • A steel or timber (LVL) beam sized for the span and load, set below the ceiling or flush within it
  • Posts, piers or masonry ends that take the beam's load, and new pad footings where the existing ones can't
  • Connections to the roof and ceiling framing, and to the brickwork in masonry houses
  • Notes on temporary propping where the order of work matters
  • Replacement bracing where the wall was a bracing wall
Fixed fee, agreed first

Wall removal and beam design

$790+ GST · $869 inc GST · starting price

A typical single wall in a single-storey house. Several walls, a storey above or a site visit are priced in your fixed quote. Design from photos and plans is available anywhere in South Australia.

Printed footing plan and steel beam plan drawings with footing details, a scale ruler, a pen and a signed certificate on a timber desk, city towers through the window
Figure 1What your builder and certifier receive: a beam layout with the footing details for the new posts, backed by calculations.

Photos of the wall

Both sides, the ceiling along it and any cracks or cornices nearby.

Measurements

Room sizes, ceiling height, wall thickness and the opening you want.

Roof framing

Which way the joists run, any struts on the wall, and tiles or sheet metal.

Plans, if you have them

Original or renovation plans help, but they aren't essential.

Beam options

Steel beam or LVL beam: which suits your opening?

Neither is better everywhere: steel carries more load in a shallower depth, while LVL is lighter and fixes like timber. The span, the load and the depth you can fit decide it.

CompareSteel beamLVL (timber) beam
Best forLong spans, heavy loads, a storey above and masonry wallsShorter spans and moderate roof or ceiling loads
DepthShallower for the same load, so easier to hide in the ceilingDeeper for the same load
HandlingHeavy; cut to length off site and often needs lifting gearLighter; carried in and cut on site like timber
FixingBolted connections, plates and timber packers to the framingNailed, screwed or bolted like other timber
Watch forCorrosion protection near damp masonry or where exposedMust stay dry; not for exposed or damp positions

General engineering practice. Your design names the exact member, size and connections.

Where does the load go once the wall is out?

The load goes to two points. A wall spreads its load along a strip footing; a beam delivers it at each end, onto a post or a short return of wall, and that concentrated load has to reach the ground through a footing big enough for it.

On a slab, each post usually needs a new pad footing cut into the slab. Over a timber floor, it needs a pier or stump under the post. Much of Adelaide sits on highly reactive clay, and every site needs its own classification, so the new footings are sized for your ground and detailed to move with the existing ones. See site classification and footings.

Masonry walls in older homes

Taking out a brick or stone wall in a villa or cottage is heavier work than a stud wall. The wall above the opening needs support while the beam goes in, the ends of the opening may need new brick piers, and old lime mortar and rubble cores behave differently from modern brickwork.

For bluestone and sandstone homes, see bluestone and heritage homes. If you're in an area with many older villas, such as Norwood, Unley or North Adelaide, we see these walls often.

How it works

How does a wall removal design work?

It takes three steps from your photos to drawings your builder can price and your certifier can approve.

  1. Send photos and measurements

    The wall from both sides, the roof space above and the room sizes, through the form on this page or the quote page.

  2. Get a fixed quote

    In under 20 minutes on average, during business hours. It says what's included and whether a site visit is needed.

  3. Receive the design

    Beam, posts, footings and connections on drawings, with calculations, ready for Building Rules Consent.

Already have a contractor's quote?

Many wall removal contractors bring their own engineer or a standard beam size. We don't sell the work, so an independent review, from $350 + GST ($385 inc GST), simply tells you whether the beam, posts and footings suit your house and your roof.

Opening up a room often comes with a bigger plan. If you're also adding a room or a storey, we can design both together: see extensions and renovations. Not sure whether you need an engineer at all? Read do I need a structural engineer?

FAQ

Wall removal and beam design FAQs

Still unsure? Call 08 7083 9853 or send photos for a fixed quote.

Do I need a structural engineer to remove a load-bearing wall?

Yes. Removing a load-bearing wall needs approval in South Australia, and the building consent application has to include structural drawings and calculations showing how the beam, posts and footings carry the load. That design comes from an engineer.

Do I need council approval to remove a wall in SA?

For a load-bearing wall, yes. Internal alterations are exempt only if they remove nothing more than fixtures, fittings or non-load-bearing partitions and don't affect the building's structural soundness. Building Rules Consent comes from your council or an accredited professional, lodged through PlanSA.

How much does an engineer cost for a wall removal in Adelaide?

Our beam designs start from $790 + GST ($869 inc GST) for a typical single wall in a single-storey house. Several walls, a storey above or a site visit add to that, and your fixed quote, sent in under 20 minutes on average, during business hours, says exactly what's included. The builder prices the building work separately.

How do I know if a wall is load bearing?

Look in the roof space: a wall under ceiling joists, roof struts or a strutting beam is probably load bearing, and many internal brick and stone walls in older Adelaide houses carry roof or ceiling loads. Only the framing confirms it, so send photos and we'll tell you.

Can you design the beam from photos?

Often, yes. Photos of both sides of the wall, the ceiling and the roof space, with the room measurements, are usually enough. Your quote says if a site visit is needed, for example to check a footing or open up a ceiling.

Can you check a wall removal contractor's beam?

Yes. Many wall removal contractors bring their own engineer or a standard beam size. An independent desktop review, from $350 + GST ($385 inc GST), checks whether that beam, its posts and footings suit your house and your roof before you sign.

The wall is already gone without approval. What now?

We inspect what was built, check the beam, posts and footings, and design any fix needed. Your council or certifier advises on the approval path, and we provide the certification they ask for.

Do you remove walls or recommend a builder?

No. We are engineering only: we design the beam, posts and footings and document them for approval. We never carry out wall removal or recommend a contractor, so the design isn't tied to anyone's quote.