Soils

Why Adelaide houses crack: reactive clay

What reactive clay is, what the state soil studies say about Keswick Clay, how deep moisture changes reach under Adelaide houses, and what the AS 2870 site classes mean for your footings.

Hand auger packed with dark reactive clay beside a borehole in cracked dry ground, with soil sample bags and a field notebook

In short

Much of Adelaide sits on highly reactive clay that swells and shrinks with moisture. A state soil study found the deeper Keswick Clay twice as reactive as the surface black earths, and Adelaide University research models moisture changes reaching about 4 m deep, up to 7 m where the soil cracks. There is no suburb-by-suburb map: every site needs its own AS 2870 classification before footings are designed.

Key takeaways

  • A 1996 study of 170 cored holes to 10 m found Adelaide's deeper clays "equally reactive" and behind "many building cracks and footing failures".
  • Moisture changes were modelled to 3.8 m in uncracked soil and up to 7 m where the soil cracks, against the 4 m recommended for Adelaide homes.
  • AS 2870 site classes run from A (little movement) through S, M, H1 and H2 to E (over 75 mm), plus P for problem sites.
  • No official map gives a suburb's site class. Every site needs its own classification.
  • Trees, leaks, ponding and uneven watering change the moisture under footings, and that is what moves them.

Two houses in the same Adelaide street can behave very differently. One stays crack-free for sixty years; the other cracks every summer. The difference is usually the ground: how reactive the clay is, how deep it goes, and what has changed its moisture. This guide covers what reactive clay is, what the state's soil studies say about Adelaide's clays, and why every footing design starts with a site classification.

Reactive clay in Adelaide: quick facts

The ground
Much of Adelaide sits on highly reactive clay
Key substrate
Keswick Clay, twice as reactive as the black earths above
Moisture depth
About 4 m recommended for Adelaide homes; up to 7 m with soil cracks
Standard
AS 2870-2011 site classes A, S, M, H1, H2, E and P
Suburb map
None official: every site is classified on its own
Our footing design
From $1,200 + GST ($1,320 inc GST), site classification arranged

What is reactive clay soil?

Reactive clay is clay that swells as it takes up water and shrinks as it dries, and it moves the footings that sit on it. A little even movement does no harm. The trouble starts when one part of a house dries out faster than another, for example under a tree or along a sunny wall, or when one corner gets wetter, from a leaking pipe or a downpipe emptying at the wall. The footings then move unevenly, and the walls crack where they are weakest.

The worst clays crack the ground open in a dry summer. On one Adelaide site, Adelaide University recorded soil cracks 5 to 40 mm wide and up to 1 m deep, deepest in March and April. Water from the first heavy rain then runs straight down those cracks, wetting the clay deep below the surface.

What clays are under Adelaide?

The benchmark study is Sheard and Bowman (1996), prepared for Mines and Energy SA with CSIRO, which logged 170 cored holes to 10 m across the Adelaide area. It found the most reactive materials were "black earths and smectite-illite rich gley clays", that "black earth soils are only half as reactive as the substrate Keswick Clay", and that "deeper clays are equally reactive and are responsible for many building cracks and footing failures".

FindingWhat it means for a houseStudy
Keswick Clay is twice as reactive as surface black earthsShallow testing alone can understate the movement; the footing has to suit the clay belowSheard and Bowman, 1996
Deeper clays are "equally reactive"Moisture changes deep down still move footingsSheard and Bowman, 1996
Footing problems linked to "substrate defects, gilgai, trees, changes to site environment, and seismicity"Trees, new paving, leaks and drainage changes all countSheard and Bowman, 1996
"Severe desiccation cracking in dry months and significant surface heave in wet months"; reaction to ponding and leaking service pipes; clay-filled valleys deeper than 8 mLeaks and ponding can heave a footing; the clay can run far deeper than a test holeSheard and others, 2016 (one north-eastern site)

Gilgai is a hummocky ground surface that forms on strongly swelling clay. Hindmarsh Clay is another named Adelaide clay in engineering papers. Neither study maps clays to suburbs.

Adelaide's earthquake hazard is also the highest of the capital cities and is part of our design checks. Of the factors in the 1996 study, though, water and trees are the ones an owner can do something about.

How deep do moisture changes reach under Adelaide houses?

About 4 m, and deeper where the ground cracks open. Adelaide University's 2026 research modelled moisture movement to 3.8 m in uncracked soil, "close to the four metres recommended for Adelaide residential construction", and up to 7 m once soil cracks let water in.

How deep soil moisture changes reach, modelled

  • Uncracked soilmodelled3.8 m
  • Recommended for Adelaide homesdesign depth cited by the study4 m
  • Soil with deep cracksmodelled, up to7 m
Figure 1Depth to which soil moisture changes reach (metres), from one study's modelling. Deeper movement means footings must be stiffer, deeper or both.Source: Adelaide University, 9 September 2026.

The study's footing example shows why it matters: in one modelled scenario a 300 mm footing beam had to become 550 mm. The same research cites an earlier estimate that almost 480,000 South Australian houses built before 1981 had incurred $1.5 billion in shrinkage-crack damage. For older homes the lesson is about water management; for new homes it is about designing the footing for the site.

What do the AS 2870 site classes mean?

A site class describes how much the ground surface is expected to move as the soil gets wetter and drier, measured as the characteristic surface movement (ys). The class sets the footing design, so a higher class means stiffer, deeper or more carefully detailed footings.

ClassGroundExpected surface movement
AMost sand and rock sitesLittle or none
SSlightly reactive clay0–20 mm
MModerately reactive clay or silt20–40 mm
H1Highly reactive clay40–60 mm
H2Highly reactive clay60–75 mm
EExtremely reactive clayMore than 75 mm
PProblem site: soft or unstable ground, uncontrolled fill, or abnormal moisture conditions such as large trees nearby or removedNeeds specific engineering

AS 2870-2011 Residential slabs and footings. Our site classification and footings service arranges the classification and designs the footings to it.

Is there a reactive soil map of Adelaide?

No official map gives the site class of a suburb or a street, and contractor pages that claim one are not reliable. The 2016 study says it plainly: "soil mapping alone cannot delineate the total swell-shrink potential". Broad patterns exist: Master Builders SA told InDaily in 2022 that reactive clays "predominate the inner ring, city and north-eastern suburbs", and the same report described eastern Adelaide's "Bay of Biscay" soil as highly reactive. But a broad pattern is not a site class. Much of Adelaide sits on highly reactive clay; every site needs its own classification.

New housing estate of brick and rendered homes with young street trees and green rolling hills behind
Figure 2Each lot in a new estate gets its own site classification. Neighbouring lots can differ, especially where the land was cut, filled or once carried trees.

How do you get a site classification in Adelaide?

You get one from a soil investigation on your block: boreholes logged and tested, then a classification to AS 2870 that the engineer designs the footings to. A building consent application must include "details in writing of any foundation investigations", so the classification is part of the paperwork as well as the design.

  1. Soil investigation

    Boreholes at the footprint, with the clay logged and sampled. Trees, fill, slopes and old footings on the site are noted.

  2. Site classification

    An AS 2870 class from A to E, or P where the site needs special treatment, with the expected surface movement.

  3. Footing design

    A slab or footing system designed for that class and the building, with drawings and calculations for your certifier.

Our footing and slab design starts from $1,200 + GST ($1,320 inc GST), with the site classification arranged for you. Extensions and granny flats need the same work: see extensions and granny flat engineering.

How do you reduce movement on reactive clay?

Keep the moisture under and around the house as even as you can through the year. Most cracking on clay starts with a change: a new tree, a leak, a downpipe that empties at the wall, or paving that stops rain soaking in on one side.

Do

  • Fix leaking taps, pipes and stormwater joints quickly
  • Run downpipes to the stormwater system, away from the walls
  • Grade paths and garden beds to fall away from the house
  • Water gardens evenly, without soaking one side
  • Plan new trees well away from footings

Don't

  • Let water pond against the footings
  • Plant thirsty trees close to the walls
  • Remove a large tree without advice: the clay can swell as it rewets
  • Install air drains in reactive clay without geotechnical advice
  • Assume a neighbour's site class applies to yours

Trees deserve their own planning. The Code's Urban Tree Canopy Overlay asks for at least one small tree per new dwelling on sites under 450 m², and more on larger sites, so new trees often end up close to new footings on clay. Existing trees have rules too: within the Regulated and Significant Tree Overlay, regulated trees (1 m trunk circumference) and significant trees (2 m) need approval to remove unless an exemption applies. Read trees and house cracks in SA.

When to call a structural engineer

Call an engineer before you build on clay, and when the clay starts showing in your walls.

  • Before you build or extend, for the site classification and footing design
  • Cracks open each summer and close in winter, or keep growing. Read cracks in walls: when to worry
  • A large tree near the house is being removed, or one has gone recently
  • A leak has been found near the footings, or water ponds against the house
  • You've been quoted for underpinning on clay and want an independent view. See underpinning assessment

Find the cause before the repair

We are engineering only, so we have no repair to sell. Send the address, photos or plans and you'll have a fixed quote in under 20 minutes on average, during business hours. Get a fixed quote.

Sources

  1. Sheard and Bowman (1996), soils of the Adelaide area, Mines and Energy SA and CSIRO (SARIG document RB9400009). 170 cored holes to 10 m; black earths and Keswick Clay
  2. Sheard and others (2016), reactive soil study, SARIG report d20011047
  3. Adelaide University, Stronger home foundations needed to withstand climate change (9 September 2026)
  4. Standards Australia, AS 2870-2011 Residential slabs and footings. Site classes and characteristic surface movement; summarised in Intrax, AS 2870-2011: a geotechnical perspective
  5. Intrax, AS 2870-2011: a geotechnical perspective
  6. InDaily, Cracking up: SA's nation-leading house faults (3 August 2022)
  7. Planning, Development and Infrastructure (General) Regulations 2017 (SA). Schedule 8 clause 2(1): foundation investigation details in a building consent application
  8. Planning and Design Code, Urban Tree Canopy Overlay, DTS/DPF 1.1
  9. D. Young, Salt attack and rising damp (2008). Air drains in reactive clay soils

FAQ

Reactive clay and site classes: FAQs

Still unsure? Call 08 7083 9853 or send photos for a fixed quote.

What is reactive clay soil?

Clay that swells as it takes up water and shrinks as it dries. Footings sitting on it rise and fall with the seasons, and uneven movement under a house is what cracks the walls.

Is Adelaide on reactive clay?

Much of it is, and the clays can be highly reactive. The ground still changes from block to block, and no official map gives a suburb's site class, so every site needs its own classification.

What is Keswick Clay?

The clay substrate named in the state's benchmark soil study of the Adelaide area. That 1996 study found surface black earths "only half as reactive as the substrate Keswick Clay", and found the deeper clays behind many building cracks and footing failures.

What do the site classes A, S, M, H1, H2, E and P mean?

They describe how much the ground surface is expected to move as moisture changes: Class A little or none, S up to 20 mm, M 20–40 mm, H1 40–60 mm, H2 60–75 mm and E more than 75 mm. Class P marks problem sites, such as soft ground or uncontrolled fill.

Is there a reactive soil map of Adelaide?

Not one that gives a site class. Research on SARIG notes that soil mapping alone can't show the full swell-shrink potential, so a site classification on your own block is the only reliable answer.

How deep do soil moisture changes reach in Adelaide?

Adelaide University's 2026 modelling found about 3.8 m in uncracked soil, close to the 4 m recommended for Adelaide homes, and up to 7 m where the soil cracks. In one scenario a 300 mm footing beam had to become 550 mm.

Can trees near my house cause cracking on clay?

Yes. Tree roots draw water from the clay and dry it unevenly under the footings. Removing or damaging a regulated or significant tree needs approval, so read trees and house cracks in SA first.

How much does site classification and footing design cost?

Our footing and slab design starts from $1,200 + GST ($1,320 inc GST), with the site classification arranged for you. You get a fixed quote in under 20 minutes on average, during business hours.